 |
|
Online demo
how%u0020much%u0020does%u0020it%u0020take…
...to build a web-enabled system?
Additional for "Web-Enabled System":
SC13 - Embedded Web-Controller
FM23 - Ethernet-transformer module
RJ45 connector
LED - Traffic Light
Resistor 470 Ohm - Pre-resistor for Traffic LED
Resistor 10 KOhm - PIO 12 of SC12
5 V DC power supply
Optional: 2 x LEDs and 2 x 560 Ohm resistor for output simulation
Connection diagram:
Layout of Plug Board:
Now built-on connect the board to, 5 V GDC and to the Network.
Further with CHIPtool: software:
The IPC@CHIP® has to be "initialized" by the CHIPtool.
The IPC@CHIP® will be now shown on the CHIPtool window. Click the right mouse button on the IPC@CHIP® line. Now, simply enter the "IP Address", "Network mask" und "Gateway" addresses.Reboot the IPC@CHIP® by click on "Config" button. The new IP Address will be now shown.
"Telnet", "FTP" and "HTTP"
The IPC@CHIP® is online
In the CHIPtool window, click right mouse button on the IPC@CHIP® and choose "Telnet".
Now, open the Windows-Telnet-Client. Default Username and Password is "tel".
Any other Telnet-Software, like Tera Term Pro, can be, also, used.
Successfully configured, the IPC@CHIP® can be seized by Telnet. As an example, enter he command "dir".
In order to be able to access the IPC@CHIP® by FTP, appropriate FTP software, like Ipswich"s WS_FTP Home, has to be used. In the FTP software, enter IP address, Username and Password (default Username and Password is "ftp").
Transfer Demo files to the IPC@CHIP®.
Then, the IPC@CHIP® has to be rebooted, either by Telnet or power off/on. After second reboot, the "IP Address", "Network mask" and "Gateway" addresses must be verified once again and eventually changed, in case of possible overwriting the CHIP.INI file, during the file transmission.
Now, the Web Server Demo can be shown. In the CHIPtool, click again with the right mouse button on the IPC@CHIP® and select "HTTP" option. The Internet Browser opens and shows the Demo. To switch on or off the LED, click on appropriate Button.
Online demo:
» dilboard.beck-ipc.com 
|
|
Tools |
|
|
|
CHIPtool Version V5.10.0.1
The CHIPtool software allows configuration of the IPC@CHIP® controller within the network, the download of new @CHIP-RTOS and the generation of a complete software image for series programming. This version now includes a FTP and a Telnet client. |
27.06.2007 |
|
 chiptool_install_v5.10.0.1.exe |
 |
1,2 MB |
|
 chiptool_releasenotes_v5.10.0.1.pdf |
|
338,81 KB |
|
|
|
examples |
|
|
|
Dilboard sample
Sample for "How much does it takes" |
17.02.2005 |
|
 dilboard_onlinedemo_stat.zip |
 |
116,56 KB |
|
|
|
 |
FTP Client
- FTP-Software - Graphischer FTP-Client für Windows 95/NT
|
|
|
Construction parts
| 1 x | SC13 | 536079 | Beck IPC GmbH | |
| 1 x | FM23 | 538430 | Beck IPC GmbH | |
| 1 x | RJ45 Buchse | 741543-U4 | Conrad Electronic SE | |
| 1 x | LED gelb, 3 mm | 156223-U4 | Conrad Electronic SE | |
| 2 x | LED grün, 3 mm | 156223-U4 | Conrad Electronic SE | |
| 1 x | 470 Ohm | 400211-U4 | Conrad Electronic SE | |
| 2 x | 560 Ohm | 400220-U4 | Conrad Electronic SE | |
| 1 x | 10 KOhm | 400378-U4 | Conrad Electronic SE | |
| 1 x | Dil Steckplatine | 527819-U4 | Conrad Electronic SE | |
|
Disclaimer:
Beck IPC GmbH makes links to third part offerings available within a special area of its website. The publishers of the websites to which these links make reference are solely liable for their contents, and particularly for damages which result from use or non-use of provided information. Beck IPC GmbH only examines these websites at the point in time at which the link is established. Any and all changes which occur at a later point in time are the responsibility of the publishers of such websites.
|
|
|
|
|
|
|
|
|
